Rastriya Krishi Vikas Yojana





It is an engine operated, walk behind type harvester suitable for harvesting and windrowing cereals and oilseed crops. The reaper consists of engine, power transmission box, pneumatic wheels, cutter bar, crop row dividers, conveyor belts with lugs, star wheels, operating controls and a sturdy frame. The engine power is transmitted to cutter bar and conveyor belts through belt pulleys. During forward motion of the reaper, crop row dividers divide the crop, which come in contact with cutter bar, where shearing of crop stems takes place. The cut crop is conveyed to one side of the machine by the conveyor belt fitted with lugs and is windrowed in the field. The crop is bundled manually and transported to threshing yard. There are no shattering losses due to vertical conveying of the crop.



Dimensions (LxWxH) (mm)

Weight (kg)

Number of crop dividers

Length of cutter bar (mm)

Cutter bar pitch (mm)

Number of strokes/min

Power requirement (hp/kW)




:      2450 x 1200 x 1000

:      145

:      4

:      1000

:      75

:      700 (0.8 m/s average speed)

:     5/3.75, diesel engine


It is suitable for harvesting rice, wheat, soybean and other cereals and oilseeds.

Cost of Machine : Rs.80,000/-



The riding type vertical conveyor reaper is a self-propelled unit in which the operator rides on the machine. Drive is given by means of two large pneumatic wheels and steering is by rear idlers. The prime mover is a 6 hp/4.5 kW diesel engine. Convenient clutch, break, steering, hydraulic system and simple power transmission are provided for ease of operation. It consists of crop row divider star wheel cutter bar (76.2 mm), conveyor belt and wire spring etc. This reaper has two forward and one reverse speed. The crop after being cut is dropped in a windrow on the side.


Overall Dimensions

Length (mm)

Width (mm)

Height (mm)

Weight (kg)

Operating speed (km/h)

Total grain losses (%)

Field capacity (ha/h)

Fuel consumption (l)

Field efficiency (%)

Labour requirement (man-h/ha)

Power requirement(hp/kW)



:      3185

:      1900

:      1450

:      1530

:      3.0-3.5

:      5.0-5.9

:      0.25-0.30

:      0.90-1.15

:      60-70

:      5-6

:      6/4.5, tractor


It is suitable for harvesting rice, wheat, soybean and other cereals and oilseed crops.

Cost of Machine : Rs.1,20,000/-











The machine consists of a 76 mm pitch reciprocating cutter bar assembly, seven crop row dividers, two vertical conveyor belts fitted with lugs, pressure springs, pulleys and gearbox for the power transmission system. The crop row dividers are fitted in front of the cutter bar assembly and the star wheels are mounted over the crop row dividers. The machine is mounted in front of the tractor and the power to the machine is given from tractor PTO with the help of intermediate shaft running beneath the chassis of the tractor and a coupling shaft. Height of the machine above ground is controlled by tractor hydraulics with the help of pulleys and steel ropes.  After the crop is cut by the cutter bar, it is held in a vertical position and crop is delivered to one side of the machine by lugged belt conveyors and fall on the ground in the form of a windrow perpendicular to the direction of movement of the machine.



Number of star wheels                            

Diameter of star wheel (mm) 

Effective cutter bar width (mm) 

Guard spacing (mm) 

Cutter bar stroke length (mm) 

Stroke per minute 

Size of belt conveyer (cm) 

Width of belt (mm) 

Diameter of conveyor pulley (mm) 

Cutter bar length (mm) 

Weight (kg) 

Power source (hp/kW)


:      7

:      270-282

:      2000-2210

:      70-80

:      75-80

:      388-675

:      2-3 ply

:      55-60

:      118-140

:      1600-2010

:      197-350

:      35/26.5, tractor



Vertical conveyor reaper is used for harvesting and windrowing of wheat and paddy crops. 

Cost of Machine : Rs.45,000/-







The combine harvester consists of cutting unit, threshing unit and cleaning and grain handling units. The cutting section includes reel, cutter bar, an auger and a feeder conveyer. Threshing section has threshing cylinder, concave and cylinder beater. The cleaning section mainly consists of walker, chaffer sieve, grain collection pan. The grain handling section consists of a grain elevator and a discharge auger. The crop after being cut is delivered to the cylinder and concave assembly through feeder conveyor where it is threshed and the grains and straw is separated in different sections. The grain can be directly loaded into the trolley.




Cutter bar length (mm)

Cutting height (mm)

Threshing drum diameter (mm)

Threshing drum length (mm)

Threshing drum speed (rpm)

Length of upper sieve (mm)

Width of upper sieve (mm)

Length of lower sieve (mm)

Width of lower sieve (mm)

Grain tank capacity (cubic meter)

Road speeds (km/h)

Weight (kg)

Power Source (hp/kW)                                                                                                                                                                                                           



:      4300

:      550-1250

:      605

:      1240

:      540-1050

:      1240

:      1215

:      1240

:      1215

:      3.28

:      2 -11.4

:      8200

:      90-110


 Uses :

Combines are used for cutting, threshing and cleaning of cereal and other crops in one operation.

Cost of Machine : Rs.14-16 lakh







The combine harvester consists of a cutting unit, threshing unit and cleaning and grain handling units. The cutting section is specially designed to harvest maize crop and the header can be fitted to conventional grain combines. Threshing section has threshing cylinder, concave and cylinder beater. The cleaning section mainly consists of walker, chaffer sieve, grain collection pan. The grain handling section consists of a grain elevator and a discharge auger. The crop after being cut is delivered to the cylinder and concave assembly through feeder conveyor where it is threshed and the grains and straw is separated in different sections.



Cutter Bar Width (mm)

Cutting Height (mm)

No. of Rows

Row Spacing (mm)

Size of threshing drum, Dia x Length (mm)

Type of Threshing drum

Speed of threshing drum (rpm)

Concave Clearance (mm)

Number of Straw Walkers

Area of straw walkers (m2)

Cleaning area (m2)

Overall Dimension (L x B)  (mm)

Min. Ground Clearance (mm)

Weight (kg).

Working capacity (ha/h)

 Power requirement(hp/kW)



:      3650

:      100- 1000

:      5/7

:      460- 685

:      600 x 1260

:      Rasp Bar

:      535 to 1210rpm

:       3-16

:       5

:       0.89

:       25

:      1500 x 4500

:      460

:       9000

:       1.00

:       75-110 56-82, Engine 


Uses :

Maize Combine is used for cutting, threshing and cleaning of Maize and can be used for harvesting other cereal crops in one operation by changing the header. 

Cost of Machine : Rs.12-14 lakh




Reaper-Binder is a unique harvesting machine that reaps the crop as well as binds it simultaneously with a twine.  This Innovative Mechanical machine ensures 100% recovery of straw with negligible grain losses at a surprisingly low cost of operation.  This machine is mainly used in Wheat, Paddy, Oats, Barley and other grain crops. 



Width of Cut (mm)

Height of Cut (mm)

Area Covered (ha/h)



Weight of Machine (Kg)



:      1200

:      30-50

:      0.4

:      10.2 /5.1 Air Cooled Diesel

:      4 Forward & 1 Reverse

:      400


  • Harvesting and Binding of Grain Crops in a single operation.
  • Used for grain crops of height up to 85 to 110 cm.
  • Harvesting and binding of 0.40 ha field in 1 hour, with consumption of 1 liter diesel only.
  • Different cutter bar can also be attached to the same machine for harvesting berseem, mentha, lucern, paddy stubbles and other fodder crops.

Cost of Machine : Rs.2,00,000/-

                                      8.7 SUGARCANE HARVESTER


It is a chopper harvester with a cleaning system and whole cane harvesters are also available. It can cut one/two rows of cane at a time.  The cane is fed between the crop dividers and is cut at the root zone by base cutter blades and simultaneously de-topped from top. The cane is then fed through the roller train and is cut by the chopper drums into small cane pieces of 24.5 to 30 cm. It is then cleaned in the primary extractor before being conveyed on the elevator. The can is then cleaned again with the secondary extractor and loaded onto a vehicle for transportation. In ideal conditions, the harvester can cut nearly 400 tonnes of sugarcane per day.


Transmission                                    :



Tyres                                                :

 Tracks                                             :

Primary Extractor                            :

Hood rotation                                  :

Elevator                                           :

Overall dimension (l x w x h) (m)  :  Engine Power (hp/kW)                   :



Two hydrostatic pumps providing variable speed (Wheel machine: 0 to 24.6 km/h) (Track machine: 0 to 9.0 km/h)

Front 14x17.5 - 14 Ply, Rear 23.5x25 - 20 Ply

Sealed track chains

Polyethylene plastic 152 cm

Hydraulically controlled

Loading to either side

15.14 x 2.50 x 6.23




It is used for harvesting sugarcane. It de-tops the cane from the top, cuts it from the base, strips the cane and cuts it into billets and also removes the trash and simultaneously loads the cut billet into the trolley moving by its side. 

Approx. Cost of Machine : Rs.105 lakhs/-



Sell automatic straw pick-up baler-Onekin international group


The tractor PTO operated machine consists of reel type straw pick up assembly, and straw compaction and tying units. It automatically picks up the residue straw from field with the help of reel which is transferred into bale chamber with the help of feeder and then straw is compressed with the reciprocating ram into a compact variable length size. It also automatically ties the knots using metal wire or nylon rope.


Length (mm)

Width (mm)

Height (mm)

Width of pick up reel

Number of knotters

Cross section of the bale chamber (mm)

Twine box capacity

No. of plunger strokes per minute

Plunger stroke length (mm)

Wheel tread (mm)

Flywheel diameter (mm)

 Power Source (hp/kW)



:      5550

:      2600

:      1950

:      1540

:      2

:      400 x 460

:      Four spools

:      75 at 2000 engine rpm

:      764

:      2100

:     560

:      35/26.5 or above tractor



Straw balers are used for baling of straw into bales of rectangular cross section.

Cost of Machine : Rs.5,00,000/-


Straw Combine Harvester


Straw combine operated by tractor PTO has cutter bar reel, feeding auger and bruising cylinder like a traditional thresher. Straw thrown and stubble left by the grain combine is collected by straw combine and delivered to the cylinder concave section, where it is cut into pieces and passed through the concave. A reciprocating cutter bar is used for reaping the standing stubbles and the portion of the straw left uncut by the combine harvester. Straw, which passes through the concave, is aspirated by a blower and fed into a trolley on rear side covered by a wire net. For recovering the left grains from the straw, a sieve system is provided below the concave.


Length (mm)

Width (mm)

Height (mm)

Length of cutter bar

Height of cut

Diameter of reel (mm)

Width of reel (mm)

Width/Dia. of threshing drum (mm)

Threshing drum speed (rpm)

Blower diameter (mm)

Blower width (mm)

Number of blowers

Machine capacity (ha/h)

Power requirement (hp/kW)



:      3370-5350

:      2145-2400

:       2210

:      1830

:      60

:      435-485

:      1920-1935

:      1025-1250/525-625

:      650

:      660

:      230

:      1-2

:      0.40

:      35/26.25 tractor or above


Straw combines are used to recover wheat straw left standing after combine operation. It also helps in recovering about 50 kg grain per hectare. 

Cost of Machine : Rs.1,25,000/-




The tractor pto operated potato digger shaker consists of a crescent/convex triangular shape-cutting blade, elevator rollers chain generally made of iron bars, power transmission device, agitator and a tractor hitching system.  The crescent shape blade helps in digging of the potatoes, which are carried to the shaking conveyor belt and finally delivered at the rear of the machine in windrows form. These are collected manually. The shaking belt helps in removal of the soil from the tubers. These machines can also be used for harvesting onions. In some models, discs are mounted in the front to cut haulm or for guiding the blade along the rows.



Length (mm)

Width (mm)

Height (mm)

Number of furrows

Working width (mm)

Size of disc ( rnm)

Weight (kg)

Power source (hp/kW)




:        2Q60

:        1195

:        1070

:        2

:        1070

:        510

:        500-525

:        35/26.25 or above, tractor


Potato diggers are used for harvesting and exposing the potato tubers.

Cost of Machine : Rs.80,000/-